Two Extreme Switch Can Ping Each Other

Explore technical resources about telecom site energy, outdoor power cabinets, BESS, optical modules, fiber connectors, off-grid base station power, and energy retrofits.

HOME / Two Extreme Switch Can Ping Each Other - Activa Netcom & Energy Systems

Related Topics:

Extreme Switch Ping Each
  • Huijue access switch ping gateway

    Huijue access switch ping gateway

    Click a switch under Device Name for which you want to perform diagnostic test. The dashboard context for the switch is displayed. Under Analyze > Tools, click Network Check. Modular switches running V200R007 and later versions As shown in Figure 15-11, ME60 is the gateway of SwitchB, and SwitchA is configured to transparently transmit Layer 2 packets. SwitchA is connected to ME60 through Eth-Trunk52 in the uplink direction and connected to SwitchB through Eth-Trunk24. A simple multi-VLAN network where a Layer 3 switch (Core-SW) handles all inter-VLAN routing. Check the link configurations between the access and core. To perform a ping test on switches, complete the following procedure: To select a group, label, site, or all devices in the filter, set the filter to one of the options under Groups, Labels, or Sites. Figure 15-9 Networking diagram for the failure to ping the gateway IP address from the IP address of the. users can get IP from DHCP server but unable to reach gateway. x)---- (GEy/y/y)Access switch (eth-trunkZ)------- （eth-trunkBB）core switch (eth-trunkAA)--- Gateway (Non-huawei device D.

    [PDF Version]
  • Fiber optic switch port zone

    Fiber optic switch port zone

    There are two main methods of zoning, the two methods being hard and soft, that combine with two sets of attributes, name and port. More recently, the differences between the 2 have blurred. All modern SAN switches then enforce soft zoning in hardware. The fabric name service allows each device to query the addresses of all other devices. Soft zoning restricts only the fabric name service, to show only an allowed subset of devices. Therefore, when a s.


  • Using a switch to aggregate multiple broadband connections

    Using a switch to aggregate multiple broadband connections

    It combines multiple ports into one link to boost speed and cut downtime. It's also known as ethernet aggregation or switch aggregation. This means fewer slowdowns, better performance, and. This wikiHow teaches you how to combine two or more Internet networks into one main network. A free Speedify account allows you to use up to 5GB of data per month. An unlimited. To actually merge two connections into a single connection where you can push the combined bandwidth as if it's coming from a single pipe requires bonding, which would either need to be provided by your ISP if all the connections are with the same ISP, or by a 3rd party if the connections are to. I have 5 internet lines in my company, and currently I am aggregating them using my firewall using ECMP technique. I have the option to route them using weighted round robin, or equal round robin or fixed source path.

    [PDF Version]
  • No internet access after connecting to the switch

    No internet access after connecting to the switch

    There are three possibilities after checking the PC's IP address: PC has no Internet access. PC has Internet with a public IP. Please double check your network topology, the switch needs to be connected behind. This article will list a few simple steps about how to do a check on the switch when the switch has no Internet access and try to solve the problem. Here we will list some common factors in this article. 0 on switch I also have the dhcp server setup with a different VLAN ID (rebooted all the devices modem, router and switch) connected the workstation. got the ip address from but no. If your Switch isn't connecting to the internet, it may be due to network issues such as a faulty connection or signal interference. Luckily, there are a few ways to get your Switch back online. This issue can stem from various causes, including.

    [PDF Version]
  • Optical Switch Signal Flow

    Optical Switch Signal Flow

    An optical switch is a device that controls the flow of light signals between different paths. At their simplest, they operate as on/off gates, allowing light to pass with low insertion loss in the open state and blocking transmission (causing high insertion loss) when closed. Figure: Optical Switch. 1State Key Laboratory of Information Photonics and Optical Communications (IPOC), Beijing University of Posts and Telecommunications, 10 Xitucheng Rd, Bei Tai Ping Zhuang, Haidian Qu, Beijing, 100876, China 2IPI-ECO Research Institute, Eindhoven University of Technology, 5600MB Eindhoven, The. Micro-electro-mechanical systems (MEMS) are miniature electrically operated mechanical devices which can be constructed using the same materials and similar processing techniques as for large scale integrated electronic components.

    [PDF Version]
  • How to turn off the main switch of the secondary distribution box

    How to turn off the main switch of the secondary distribution box

    At the main supply find the main switch that controls the supply to that DB. Place a padlock through the switch where possible, to lock it in the. Can you turn off the main circuit breaker yourself? Yes, you can turn off your main circuit breaker yourself, and it's a crucial skill for home safety and troubleshooting. Laterals can be directly connected to main trunks, but are more commonly protected by protective devices such as fuses. So I'm wondering what to do to cut the power. Where the switch has an internal fuse remove it and take it with you. It is an essential component of any electrical system as it provides a safe and convenient way to. Main Switch: This serves as the central control to turn off or on the entire system, useful for emergencies or maintenance.

    [PDF Version]
  • The core layer is implemented using a Layer 2 switch

    The core layer is implemented using a Layer 2 switch

    Layer 2 switches are fundamental components in modern networking, playing a crucial role in managing data traffic within local area networks (LANs). Core Layer: The core layer is the backbone of the hierarchy network. The primary transmission and routing of data signals take place at the core layer only. Each layer is served by specialized switches, with the access switch connecting end-user devices, the distribution switch aggregating traffic and enforcing policies, and the core switch acting as. A core switch is a high-capacity switch that integrates with the other switches and acts as a backbone of the network.


  • Place the fiber optic switch in the weak current box

    Place the fiber optic switch in the weak current box

    The home optical fiber distribution boxis generally located in the weak current box of the home. The weak wire has a small space, which is not conducive to the heat dissipation of the equipment, and it is made.


Telecom Site Energy & Optical Insights